I closed up any gaps with small wedges I cut from scrap walnut in the miter box. Maybe I could have done better with a shooting board. The rough pieces were glued to a notch cut into the frame corners and planed to size after the glue had dried.Īnd there is no way I can claim perfect miters. I cut the blank into sections and used a chisel to split the blank. I used a pink ivory pen blank for the splines so there is a contrast against the walnut. Instead of cutting splines through the miters (like this example), I tried to simplify things by placing the spline on the outside edge in a diagonal rabbet. The miters were cut taking the width of the rabbet into account: it was a simple case of using the glass resting in a rabbet to mark out where to make the cuts. I used a rabbet plane to cut a 1/4 by 1/4 rabbet around the edges for the glass. I used a jointer plane to ensure each frame segment had the same dimensions. The wood is a piece of walnut I ripped into 1 inch by 3/4 inch strips. The frame was junk, but the hardware is great. If you want to hang the frame, simply hammer in a sawtooth hanger (or two) along the top.For the glass and cardboard stand/backing I simply bought the cheapest 8 by 10 inch frame I could find (~$3. When I want to change the print, it’s easy to pop the staple out, take the print off the foam board, and tape a new one in, with no damage to the print or frame. Then I just flipped the foam board over, center the print in the frame, and stapled the foam board right to the frame. I found that the easiest way to attach a print or photo was to tape it to a piece of stiff foam board (found at the dollar store) that I trimmed to slightly smaller than frame size: I really want to make another one and pick a better stain, though, because I think that could be gorgeous. I used 50 cent acrylic craft paint from Walmart and mixed in a few drops of water to thin it out a bit so the wood grain would show through: I picked a robin’s egg blue because I knew that would like nice against a chalkboard printable. I stained it, then hated how it looked, so I sanded most of the stain off and just painted it instead. I put heavy books on it to make sure the corners all laid flat and left it to dry for a couple of hours. I used a lot of wood glue, pushed my pieces as close together as possible, and asked one of my boys to hammer in a couple of joiners across the seam. I was looking for something inexpensive and convenient, so I found these wood joiners for a buck fifty: You could also use a metal brace that you screw into the pieces you’re attaching together. I’ve seen v-nails recommended, but I couldn’t find them at Home Depot. To put your frame together, you’ll need wood glue and some sort of joiner. If you do that, you’ll want to cut your pieces like this: You can just make a frame without mitered corners. If you don’t have a miter saw, don’t worry. I accomplished this by sawing through both pieces at once on the miter saw. This will ensure that your mitered corners line up perfectly. The exact dimensions are not that important however, it IS important that both long pieces are exactly the same lenght, and both shorter pieces are exactly the same length. For a 16×20 print, I had pieces that looked like this: When cutting your pieces, remember that the short side (inside) of each board should be about an inch shorter than the height or width of your print. I used a miter saw set at 45 degrees to miter the corners. I got the 8 ft length for a frame for a 16×20 print. I used a 4 inch wide pine board from Home Depot (which is actually about 3.5 inches wide). (If you’d like to find even more tutorials for building photo frames, check out 20 best DIY frame tutorials.) Turns out it’s not! Keep reading for instructions on how to make a simple wood frame. I figured it couldn’t be too hard to make my own using a $5 pine board from Home Depot. What’s a little more difficult is finding cool frames that don’t cost much, especially for a large print. There are so many free printables available now that it would be easy to find one that’s perfect for every single room is your house. Subway art, chalkboard art, calligraphy, awesome quotes in cool fonts, etc.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |